
Maraging Steel 350 Plate
Maraging Steel 350 Plate is a nickel-maraging alloy that is comparatively soft, but exceptionally tough. It can also be readily machined and formed to various specifications. In addition, the aging process of it raises the hardness to a level sufficient for many tooling applications.
maraging c350 Sheet is a nickel/cobalt steel alloy that is essentially carbon-free, it has other alloying elements such as molybdenum, aluminum and titanium. This combination creates a superior maraging steel with a variety of features such as extremely tough, corrosion resistance & crack propagation, readily weldable, uniform, predictable shrinkage during heat treatment, easily nitride, easily weldable.
c350 maraging steel material is used for numerous industrial applications, some of which include wind tunnel models, missile & rocket motor cases, landing gear components, high performance shafting, gears & fasteners, aerospace, extrusion tooling, die casting, etc.
vascomax c350 Plates can be heat treated to 900 F +/- 10 holding at temperature for 6 hours then cooling at room air temperature. During the aging treatment it shrinks uniformly and predictably on all dimensions .001 in/in
In the annealed condition maraging steel 350 is comparable to 4340. However, when it is aged, the type of cutting tool and speeds has to be changed and firm tool supports, rigid equipment, sharp tools and abundant coolant are essential.
vascomax 350 is weld able without preheat, in both the annealed and aged condition. Only an aging heat treatment is needed to restore in the weldedability.
maraging 350 is produced by vacuum arc re-melting and provides a very high strength nominally 350 ksi tensile with an above average level of toughness. It retains its strength up to 450°C and good notch impact is maintained down to - 50°C and below.
Type | Description | USA FOB Price | Malaysia FOB Price | Europe FOB Price | Singapore FOB Price | Saudi Arabia (KSA) FOB Price | |||||
---|---|---|---|---|---|---|---|---|---|---|---|
Unit Per mtr | Unit Per mtr | Unit Per mtr | Unit Per mtr | Unit Per mtr | |||||||
maraging Steel 350 Plate | Size : 30mm x 500 x 500 | US $ | 79.53 | Malaysia Ringgit | 323.69 | Euro | 66.81 | Singapore Dollar | 106.57 | Saudi Riyal | 298.24 |
Maraging Steel 350 Plate
maraging c350 Sheet
c350 maraging steel Plate
vascomax c350 Plates
maraging steel 350 Sheet
DIN 1.6356 maraging 350 Sheet
Symbol | Element | Nominal % |
---|---|---|
C | Carbon | 0.03 max |
Si | Silicon | 0.10 max |
Mn | Manganese | 0.10 max |
Ni | Nickel | 18.50 |
Co | Cobalt | 12.00 |
Mo | Molybdenum | 4.80 |
Ti | Titanium | 1.40 |
Al | Aluminum | 0.10 |
Fe | Iron | Balance |
Properties | Metric | Imperial |
---|---|---|
Tensile strength | 1140 MPa | 165000 psi |
Yield strength (@ strain 0.200%) | 827 MPa | 120000 psi |
Bulk modulus (typical for steel) | 140 GPa | 20300 ksi |
Shear modulus (estimated from elastic modulus) | 77 GPa | 11200 ksi |
Elastic modulus | 200 GPa | 29000 ksi |
Poisson’s ratio | 0.3 | 0.3 |
Elongation at break (in gage length 4.5 times the square root of the area) | 18% | 18% |
Reduction of area | 70% | 70% |
Properties | Metric | Imperial |
---|---|---|
Density | 8.08 g/cc | 0.292 lb/in³ |
Temperature | Time | Resulting Hardness |
---|---|---|
900/925 °F | 6 hrs | 55/60 Rc |
950 °F | 3 hrs | 56/60 Rc |
Operation | Tool Material | Tool Geometry | Depth of cut | Width of cut | Feed | Cutting Speed | Wearland | Cutting Fluid |
---|---|---|---|---|---|---|---|---|
Turning | M2 or T-15 | BR: 0°; SR: 10° SCEA: 15°; ECEA: 5° Relief: 5°; NR: 0.030 in |
0.060 in | -- | 0.009 in/rev | 80 ft/min | 0.060 in | Soluble oil (1:20) |
Turning | C3 | BR: -5°; SR: -5° SCEA: 15°; ECEA: 15° Relief: 5°; NR: 0.030 in |
-- | 0.009 in/rev | 475 | 0.010 | Soluble oil (1:20) | |
Face milling | M2 or M-7 | AR: 5°; RR: 5°; CA: 45° ECEA: 10°; CI: 8° |
0.060 | 2 in | 0.005 in/tooth | 140 | 0.060 | Highly chlorinated oil |
Face milling | C2 | AR: 10°; RR: 0° CA: 45° ECEA: 10° CI: 8° |
0.060 | 2 | 0.005 in/tooth | 330 | 0.015 | Dry |
Peripheral end milling | M2 | Helix Angle: 30°; RR: 10° CA: 45° x 0.060 in; CI: 7° |
0.250 | 0.750 | 0.004 in/tooth | 225 | 0.012 | Soluble oil (1:20) |
End mill slotting | M2 | Helix angle: 30°; RR: 10° CA: 45 x 0.060 in; CI: 7° |
0.250 | 0.750 | 0.002 in/tooth | 140 | 0.012 | Highly chlorinated oil |
Drilling | M1 | 118° plain point; CI: 7° | 0.500 (through hole) | -- | 0.005 in/rev | 100 | 0.015 | Highly sulfurized oil |
Reaming | M2 | Helix angle: 0°; CA: 45° CI: 7° |
0.500 (through hole) | -- | 0.009 in/rev | 60 | 0.006 | Highly sulfurized oil |
Tapping | M1 | 2 flute plug; 75% thread | 0.500 (through hole) | -- | -- | 150 | Undersize threads | Highly sulfurized oil |
c350 maraging steel material Supplier