Aesteiron Steels
Aesteiron Main Page Aesteiron -Sheet Plate exporter All Steel Plate & Industrial Goods Grade Quality -Sheet Plate exporter Contact Steel Plate Exporter Send Inquiry Now for Factory Rate contact Steel Plate Exporter
A106 GR. B Carbon Steel Seamless Pipes Manufacturer and Exporter

A106 GR. B Carbon Steel Seamless Pipes

A106 GR. B Carbon Steel Seamless Pipes / ASTM A106 Gr. B/C, API 5L Gr. B, ASTM A53 Gr. B Pipes Tubes

A106 GR. B Carbon Steel Seamless Pipes Manufacturer and Exporter

You are here - Home / Products / Carbon Steel / A106 GR. B Carbon Steel Seamless Pipes

Renowned manufacturers & suppliers of A106 GR. B Carbon Steel Seamless Pipes, ASTM A106 Gr. B/C, API 5L Gr. B, ASTM A53 Gr. B Pipes Tubes

We export high quality A106 GR. B Carbon Steel Seamless Pipes & ASTM A106 Gr. B/C, API 5L Gr. B, ASTM A53 Gr. B Pipes Tubes

ASTM A106 GR. A / GR. B / GR. C Seamless Carbon Steel Pipes

ASTM A106 Seamless Pressure Pipe (also known as ASME SA106 pipe) is commonly used in the construction of oil and gas refineries, power plants, petrochemical plants, boilers, and ships where the piping must transport fluids and gasses that exhibit higher temperatures and pressure levels.

This specification covers seamless carbon steel pipe for high-temperature service

Sizes (Seamless): 1/2" NB - 60" NB
Sizes (ERW): 1/2" NB - 24" NB
Sizes (SAW): 16" NB - 100" NB
Wall Thickness available:
Schedule 20 - Schedule XXS (heavier on request) up to 250 mm thk.Material Grades

 High Temperature Seamless P
ipe
ASTM A106 Gr. B/C, API 5L Gr. B, ASTM A53 Gr. B
Heat Exchanger Seamless Tube ASTM A179
Low Temperature Seamless Pipe ASTM A333 Gr. 3/6
Low Temperature Seamless Tube ASTM A334 Gr. 6
High Yield Seamless Pipe API 5L Gr. X42/X46/X52/X56/X60/X65/X70/X80 PSL-1/PSL-2
High Yield Seamless Pipe ISO 3183 Gr.L245, L290, L320, L360, L390, L415, L450, L485
Atmospheric & Low Temp EFW Pipes ASTM A671 Gr. CC60/CC65/CC70
High Pressure & Moderate Temp EFW Pipes ASTM A672 Gr. B60/B65/B70/C55/C60/C65/C70
High Yield ERW/SAW Pipe API 5L Gr. X42/X46/X52/X56/X60/X65/X70/X80 PSL-1/PSL-2
High Yield ERW/SAW Pipe ISO 3183 Gr.L245, L290, L320, L360, L390, L415, L450, L485

Additional Testing :
NACE MR0175, NACE TM0177, NACE TM0284, HIC TEST, SSC TEST, H2 SERVICE, IBR, etc.

Dimensions :

All Pipe is manufactured and inspected/tested to the relevant standards including ASTM, ASME, API.

Chemical Composition ASTM A106 Carbon Steel Pipes Grades

  Grade A Grade B Grade C Total of Cr, Cu, Mo, Ni, and V shall not exceed 1%
Carbon max. % 0.25 0.30 0.35
Manganese % 0.27 to 0.93 0.29 to 1.06 0.29 to 1.06
Phosphorous, max. % 0.035 0.035 0.035
Sulfur, max. % 0.035 0.035 0.035
Silicon, min.% 0.10 0.10 0.10
Chrome, max. % 0.40 0.40 0.40
Copper, max. % 0.40 0.40 0.40
Molybdenum, max. % 0.15 0.15 0.15
Nickel, max. % 0.40 0.40 0.40
Vanadium, min.% 0.08 0.08 0.08

Permissible Variations in Wall Thickness

The minimum wall thickness at any point shall not be more than 12.5% under the nominal wall thickness specified.

Permissible Variations in  Weights per Foot Weight of any length shall not vary more than 10% over and 3.5% under that specified. NOTE -- NPS 4 and smaller -- weighed in lots. Larger sizes shall be weighed separately by length. Permissible Variations in Outside Diameter
Outside Diameter at any point shall not vary from standard specified more than:

NPS [DN Designator] Over Under
in. mm in. mm
1/8 to 1-1/2 [6 to 40], incl 1/64 (0.015) 0.4 1/64 (0.015) 0.4
Over 1-1/2 to 4 [40 to 100], incl 1/32 (0.031) 0.8 1/32 (0.031) 0.8
Over 4 to 8 [100 to 200], incl 1/16 (0.062) 1.6 1/32 (0.031) 0.8
Over 8 to 18 [200 to 450], incl 3/32 (0.093) 2.4 1/32 (0.031) 0.8
Over 18 to 26 [450 to 650], incl 1/8 (0.125) 3.2 1/32 (0.031) 0.8
Over 26 to 34 [650 to 859], incl 5/32 (0.156) 4.0 1/32 (0.031) 0.8
Over 34 to 48 [850 to 1200], incl 3/16 (0.187) 4.8 1/32 (0.031) 0.8

Tensile Requirements

  Seamless
  Grade A Grade B Grade C
Tensile Strength, min., psi 48,000 60,000 70,000
Yield Strength, min., psi 30,000 35,000 40,000

Number of Tests Required

  NPS On One Length from Each Lot of
Tensile 5 and smaller 400 or less
6 and larger 200 or less
Bending 2 and smaller 400 or less
Flattening 2 through 5 400 or less
6 and over 200 or less

Hydrostatic Testing

Inspection test pressures produce a stress in the pipe wall equal to 60% of specified minimum yield strength (SMYS) at room temperature. Maximum Pressures are not to exceed 2500 psi for NPS3 and under 2800 psi for the larger sizes. Pressure is maintained for not less than 5 seconds.

Mechanical Tests Specified

Tensile Test - NPS 8 and larger - either transverse or longitudinal acceptable
Smaller than NPS 8 - weighed in lots. Larger sizes - by length.
Flattening Test - NPS 2-1/2 and larger.

Bending Test (Cold) - NPS 2 and under.

  Degree of Bend Diameter of Mandrel
For Normal A106 Uses 90 12 x nom dia. of pipe
For Close Coiling 180 8 x nom dia. of pipe
Carbon Steel Inventory:

Available Pipes & Tubes Stock at Aesteiron

Pipes Gradewise Stock At a Glance:-
Tubes Gradewise Stock At a Glance:-
Nickel Alloys Pipes & Tubes Stock At a Glance:-
Top Sellers Pipes & Tubes At a Glance:-
List of Countries where Aesteiron supply Carbon Steel Pipes & Tubes:-

List of Countries where Aesteiron supply Pipes / Tubes :-

Please note:
ASTM A312 / A312M - 13 Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

Products & Materials

Products

Tools

A106 GR. B Carbon Steel Seamless Pipes      

Manufacturing Products

Specialized Material

Quick Contact

Quick Enquiry

We Export

Stainless Steel
Duplex Stainless Steel
Super Duplex
Nickel Alloys
Inconel
Incoloy
Hastelloy
Monel
Alloy 20
Carbon Steel
API 5L
Alloy Steel
Titanium
Aesteiron Steels LLP
107, Kika Street, 4th Floor,
village - Ustane, Tal - Ambernath,
Umrao Bhavan, Gulalwadi,
Mumbai - 400004, India

Tel No.: +91 22 23453040

For quick reply-

Email: info@aesteiron.com

Worldwide Exports

 

Home   |   Contact Us   |   Site Map  |   Blog

Copyright © 1998 - 2014 Aesteiron Steels LLP | Website & SEO (Search Engine Optimization) by Mesotek